Home > Boot Cannot > Boot Cannot Open Bootdisk

Boot Cannot Open Bootdisk

Switch Is in Continuous Booting Loop or in ROMmon mode The switch can go into a continuous booting loop or ROMmon mode for any of these reasons: The boot variables are Under System Startup, select your Default operating system Still under System Startup, click the Edit button. Use the Arrow keys to navigate. On the Advanced tab, click Settings under Startup and Recovery. Check This Out

Invoke this application for disaster recovery. Router(boot)#write memory Building configuration... [OK] !--- Verify the settings. You can alter the description to your own liking but must use the = and enclose the description between the quotes. The file was transferred via FTP as ASCII instead of binary. have a peek at this web-site

This will contain a copy of Boot.ini plus the other boot files. Copyright © LarryM 1998-2015 thpc@mail.com Skip to ContentSkip to FooterSolutions Transform to a Hybrid Infrastructure Protect Your Digital Enterprise Empower the Data-Driven Organization Enable Workplace Productivity Cloud Security Big Data Mobility At that point, you cannot boot the switch in order to run Cisco IOS Software on it.

These caveats apply to the Xmodem procedure: The Xmodem procedure does not save the downloaded image into the MSFC boot Flash. End with CNTL/Z. DAVID DEETHS has worked in Sun's Enterprise Engineering group for four years. Important side note for anyone with a SUP720 - you can't load an IOS image over serial or TFTP with the ROMMON.

The supervisor can require a high-speed fan tray. RP has 12.2(17r)SX7 installed (I guess that does not matter anyway). y/n [n]: y Note, if the console port is attached to a modem, both the console port and the modem must be operating at the same baud rate. http://www.gossamer-threads.com/lists/cisco/nsp/170307 This step of the procedure presents both methods, and you can choose the one to use.

It's virtually always set to 0 (zero). Press RETURN to get started! !--- This indicates that the switch has moved into the RP mode properly. !--- Output suppressed. 6500>enable 6509#configure terminal Enter configuration commands, one per line. Note:If the RP previously had the MSFC boot image (c6msfc-xx) on the boot Flash, the Catalyst 6500/6000 could boot all the way up to the router prompt (Router >). See More 1 2 3 4 5 Overall Rating: 5 (1 ratings) Log in or register to post comments branfarm1 Sat, 11/05/2011 - 20:40 Thanks for the replies.

Format operation will destroy all data in "bootflash:". check here You can lose the image in one of these ways: A deletion or corruption occurred during the download. If you found that the switch went to SP ROMmon, you do not need to hit the break sequence. Download Order Features Screenshots Video Guide FAQ Feedback Support Contacts Site map Active [email protected] Boot Disk Boot Disk FAQ: boot disk cannot see the drives Contents > The [email protected] Boot Disk

Writing image to bootflash:c6msfc-boot-mz.121-4.E1 !!!!!!!!!!!!!!!!!!!!!! his comment is here Router-sp# BOOT variable = bootflash:c6sup11-jsv-mz.121-6.E,1; CONFIG_FILE variable = BOOTLDR variable does not exist Configuration register is 0x2102 Router#dir sup-bootflash: Directory of sup-bootflash:/ 1 -rw- 13465088 Jan 12 2000 22:39:01 c6sup11-jsv-mz.121-6.E 15990784 For instructions on how to recover the Supervisor Engine from this issue, see the Recovery Procedure section of this document. KrawetzLimited preview - 2003 About the author(2002)JOHN S.

Router(boot)(config)#config-register 0x2102 !--- Set the boot variable. Now type ATTRIB +R +S +H C:\BOOT.INI and reboot. [top of page] #8: Use THPC's Rescue Boot Disk if Boot.ini is on an NTFS partition If you have made THPC's Rescue Chksum: Verified! this contact form After replacing the battery I was able to flash the ROMMONs. ;) Same adapter + same flash card boots in another Sup720 with same ROMMON versions.

Any mounting software will convert it for you, last time I needed to do this was about 5 years ago and I used daemon tools I believe. Tags: pvcreate View All (1) 1 Kudo Reply unx_wrks Advisor Options Mark as New Bookmark Subscribe Subscribe to RSS Feed Highlight Print Email to a Friend Report Inappropriate Content ‎05-21-2013 08:57 ERROR in newfs"exitfiTLOG "Doing lvlnboot -b /dev/vgaltboot/lvstand"lvlnboot -b /dev/vgaltboot/lvstandERCHECK "lvlnboot -b /dev/vgaltboot/lvstand"TLOG "Doing lvlnboot -r /dev/vgaltboot/lvroot"lvlnboot -r /dev/vgaltboot/lvrootERCHECK "lvlnboot -r /dev/vgaltboot/lvroot"TLOG "Doing lvlnboot -s /dev/vgaltboot/lvswapA"lvlnboot -s /dev/vgaltboot/lvswapAERCHECK "lvlnboot -s /dev/vgaltboot/lvswapA"TLOG "Doing

Reseat the fan tray.

Note: Bootcfg recognizes only XP, 2K, or NT installations. You cannot Tab in order to complete them, and you must use the correct command syntax in order to copy the boot image successfully into the RP boot Flash. The RP boot loader image is approximately 1.8 MB and takes about 45 minutes to load. For serial, its particularly > deceptive in that the command is there, but will fail every single time. > > Yay Cisco! > > > -- > Brielle Bruns > The

Bootcfg commands: bootcfg /list - displays the current situation bootcfg /add - scans for, & optionally adds, XP, 2K, NT installations bootcfg /rebuild - displays/adds the OSs located bootcfg /scan - This section provides the current recovery to perform if you find that you cannot get the Supervisor Engine 720 out of ROMmon. Router(boot)#dir sup-slot0: %Error opening sup-slot0:/ (Invalid argument) Instead, use one of these two commands in order to copy the boot image. navigate here The command to use depends on the software version: If you run any version that is earlier than c6msfc-boot-mz.121-12c.E2, the command is download.

did it throw the same error again?

© Copyright 2017 mediastartpage.com. All rights reserved.